Idc Smartstep Manual

Idc Smartstep Manual 5,0/5 2484 reviews

Manuals, brochures and other documents, whether electronic or in writing, relating to. The special flat cable and IDC. 48% that of the SmartStep series.

• SMARTSTEP 2 SERVO SYSTEM A n e w s t e p i n s e r v o d r i v e s i m p l i c i t y » P r e c i s e a n d c o s t - e f f e c t i v e ». • Getting started quickly CX-Drive is a single, easy-to-use software tool for configuring, commissioning and maintaining both inverters and servos.

SmartStep 2 is fully supported with a wide range of features making the servo drive set-up easier and faster than ever: Auto-tuning •. • A compact design that’s easy to connect Although it has more functionality than previous models, SmartStep 2 has a compact design with an ultra-small footprint that saves considerable space. In addition, SmartStep 2 can be easily integrated with other automation devices such as the CP1L compact machine controller and NS operator terminals, helping to make an efficient and cost-effective machine design. Nissin 340t flash manual update. • • Servomotors with IP65 as standard and shaft oil seal available • Motors with brake as option Ratings • 230 VAC single-phase 50 W to 750 W (0.16 to 2.4 Nm) System configuration (Refer to chapter SmartStep servo motors) SmartStep 2.

• Between power supply/power line terminals and frame ground: 0.5 MΩ min. (at 500 VDC) Dielectric strength Between power supply/power terminals and frame ground: 1,500 VAC for 1 min at 50/60 Hz Between each control signal and frame ground: 500 VAC for 1 min Protective structure Built into panel (IP10). Archi cad 15. • G05030H G020030H G40030H G75030H (R88M-) G10030H GP20030H GP40030H GP10030H Servodrive part names SmartStep2 Servo Drive (100 - 400 W models) Alarm indicator (ALM) Power supply indicator Communications connector (CN3) Control I/O connector (CN1) Encoder input connector (CN2) Motor connector (CNB) • Blank No brake 200 W Brake 400 W 750 W Rated Speed (r/min) Voltage and encoder specifications 3000 H: 230 V with incremental encoder Servo motor / servo drive combination Servo motor Family Voltage Speed Rated torque Capacity Model Cylindric.

• 3 times each in the X, Y, and Z directions Insulation resistance 20 MΩ min. At 500 VDC between the power terminals and FG terminal Dielectric strength 1,500 VAC (50 or 60 Hz) for 1 minute between the power terminals and FG terminal Run position Any direction Insulation grade. • Allowable thrust load Weight Without brake With brake Encoder resolution Phase A and B: 2,500 pulses/rotation, Phase Z: 1 pulse/rotation 130 × 120 × t10 (Al) 170 × 160 × t12 (Al) Radiation shield dimensions 3.0 × 10 9.0 × 10 9.0 ×. • 2 x M4 165±1 179±1 190 180 output 2 x 170 mm output connector flexes flexes to servo drive power supply input 1 x 130 mm output flexes Filter model Rated current Leakage current. • (Straight shaft with key) Brake connector Encoder connector Servomotor connector M (depth: L) Four, Z dia. C × C Flat type 3000 r/min (230 V, 100 W - 400 W) Dimensions (mm) Without With Flange surface Shaft end Aprox.

Mass (Kg) brake. • Frame ground *1. An External Regeneration Resistor can be connected. Connect this resistor if the regenerative energy exceeds regeneration absorption capacity in the Servo Drive. Note: 1.The dynamic brake operates when the main circuit power supply or the control circuit power supply is turned OFF. • Shell *1 B3-B2 are short-circuited. If the internal regenerative resistor is insufficient, remove the wire between B2 and B3 and connect an external regen- erative resistor between B1 and B2.

Step

*2 Use only when an absolute encoder. If a backup battery is connected, an encoder cable with a battery is not required. • Terminal block General purpose signals Filter (with pulse output) ABCDE Note: The symbols. Show the recommended sequence to select the components in a SmartStep 2 servo system Servo motor Cylindrical servo motors (3,000-r/min) Symbol Specifications Servo motor model Compatible servo drives. • CJ1W-NC414 XW2Z-500X 10 m XW2Z-010X Terminal block for external signals ( with M3 screw and for pin terminals) XW2B-20G4 Terminal block ext. Signals ( with M3.5 screw and for fork/round terminals) XW2B-20G5 Terminal block ext.

Signals ( with M3 screw and fork/round pin terminals) • External Regenerative Resistor Connection Cable, 2 meters R7A-CLB002RG Parameter unit & computer software Specifications Model Parameter copy unit (with cable) R88A-PR02G Configuration and monitoring software tool for servo drives and inverters. (CX-drive version 1.8 or higher) CX-drive AC servo systems. • Brake cable Terminal block General purpose signals (with pulse output) ABCDE Note: The symbols.